- ADAFRUIT TRINKET USB SERIAL INSTALL
- ADAFRUIT TRINKET USB SERIAL SERIAL
- ADAFRUIT TRINKET USB SERIAL 32 BIT
- ADAFRUIT TRINKET USB SERIAL CODE
DMA-NeoPixel support on one pin so you can drive pixels without having to spend any processor time on it. Three pins can also be used as hardware capacitive touch sensors with no additional components requiredĬan drive NeoPixels or DotStars on any pins, with enough memory to drive 8000+ pixels.
Two high speed PWM outputs – for servos, LEDs, etc
ADAFRUIT TRINKET USB SERIAL CODE
We gave the M0 pads the exact same names as the original Trinket so all your existing Arduino code will work exactly the same as-is without changes True analog output on one I/O pin – can be used to play 10-bit quality audio clips
Three of the I/O pins can be used for 12-bit analog input (ATtiny85 does not have native USB)Ĭan be used with Arduino IDE or CircuitPythonĪll 5 GPIO pins are available and are not shared with USB – so you can use them for whatever you like!įive GPIO pins with digital input/output with internally connected pullups or pulldowns
ADAFRUIT TRINKET USB SERIAL SERIAL
Native USB supported by every OS – can be used in Arduino or CircuitPython as USB serial console, Keyboard/Mouse HID, even a little disk drive for storing Python scripts.
ADAFRUIT TRINKET USB SERIAL 32 BIT
Updating ATtiny85 8-bit AVR for ATSAMD21E18 32-bit Cortex M0+Ģ56KB Flash – 32x as much as 8 KB on ATtiny85ģ2 KB RAM – 64x as much as 512 bytes on ATtiny85Ĥ8 MHz 32 bit processor – 6x as fast as ATtiny85 (not even taking into account 32-bit speedups) Same size, form-factor, and pinout as classic Trinket Here are some of the updates you can look forward to when using Trinket M0: Please check out the Trinket M0 CircuitPython guide for a list of capabilities and quick-start code examples – CircuitPython is easier to code but not as low-level and complete as Arduino. When you're done, unplug the Trinket M0 and your code will go with you.
ADAFRUIT TRINKET USB SERIAL INSTALL
No installs, IDE or compiler needed, so you can use it on any computer, even ChromeBooks or computers you can't install software on. Edit main.py with your favorite text editor to build your project using Python, the most popular programming language. When you plug it in, it will show up as a very small disk drive with main.py on it.
The most exciting part of the Trinket M0 is that while you can use it with the Arduino IDE, we are shipping it with CircuitPython on board. It's just as small, and it's easier to use, so you can do more. The Trinket M0 has swapped out the lightweight ATtiny85 for a ATSAMD21E18 powerhouse. We've taken the same form factor we used for the original ATtiny85-based Trinket and gave it an upgrade. It's our lowest-cost CircuitPython programmable board! Perfect for when you don't want to give up your expensive dev-board and you aren't willing to take apart the project you worked so hard to design. We wanted to design a microcontroller board that was small enough to fit into any project, and low cost enough to use without hesitation. If you throw in pump speed, it could get complicated, but still possible.The Adafruit Trinket M0 may be small, but do not be fooled by its size! It's a tiny microcontroller board, built around the Atmel ATSAMD21, a little chip with a lot of power. You could program a self-tuning PID controller to adjust fan speed. Instead of doing it in AIDA64, you could get a display in your case that doesn't rely on the OS running and make it OS agnostic. You could use a thermocouple or RTD instead of a NTC thermistor. It wouldn't be cheap, but you could use something from Omega and the like.ĭifferent type of temp sensor. You could use a very accurate flow sensor. Those sensors also have versions that work on 12 V or 5 V so you can power them from a SATA or Molex.įlow sensor. If you have individually sleeved cables, there are current clamp style sensors that could let you measure current on the PCI-E power cables and CPU power cables.
One that is in the 0-10 psi range would likely work.Ĭurrent sensors. You have 12 V and 5 V (excitation voltage) pressure sensor that return either a current loop or voltage signal. Here are some ideas if you ever want to go nuts with sensor readouts for the heck of it: You solution is however much more versatile in the end. The advantage of a controller like a Quadro is the ease of use. Share your rig with us! (remember to include a parts list with case)Īsk for advice, we're here to help as well as show off!Ī Guide to Hardline tubing - PETG and AcrylicĪ Guide to Hardline tubing - Brass and Carbon Fibre Post simply asking for a parts list, you need to do your own research first!Ĭheck through our sidebar and wiki resources before posting questions Make sales posts outside of the official sticky (it is refreshed weekly) Official Manufacturer Support/Discussion ThreadsĪdvise others without suitable experience Official Manufacturer Support Threads: EKWB | Watercool | Official Subreddit Discord.